|
Product Details:
Contact Now
Chat Now
|
| Model: | YY-WL51 | Overall Length: | 51mm (2 Inch) |
|---|---|---|---|
| Flange Head Diameter: | 14mm (0.55 Inch) | Tapered Tip Section: | 15mm (0.59 Inch) |
| Wire Hole Diameter: | 2mm (0.078 Inch) | Body Structure: | Spiral Ribs With 4 Expansion Slots |
| Material: | Carbon Steel, Zinc Plated | Wire Capacity: | 1.5-2.0mm Suspension Wire |
| Substrate: | 9.5-12.5mm Gypsum Board | Reference Working Load: | 5kg Per Fixing In 12.5mm Board |
| Installation: | Tapered Tip Driven Up Into The Board, Flange Flush At The Underside, Wire Through The Head Hole | Application: | Gypsum Board Ceilings, LED Panel Lights, Signage, Light Ductwork |
| Cable Type: | 1.5-2.0mm Aircraft Cable, Galvanised Or Stainless | System: | Wire Cable Hanging System, Adjustable At The Head By Twisting |
| Highlight: | aircraft cable adjustable fittings,wire cable hanging system,gypsum board wire lock anchor |
||
A 51mm steel anchor from our precision aircraft cable adjustable fittings range, made for wire cable hanging systems in finished plasterboard ceilings. The 15mm tapered tip is driven up into the board first; the spiral-ribbed body self-threads through the gypsum core, and the Ø14mm flange stops flush against the underside of the board. The suspension wire passes through the Ø2mm head hole and is twisted off, so from below you see a flat disc with the wire coming out of it – nothing else.
![]()
|
Tapered tip enters first The 15mm four-facet point is driven up into the plasterboard and starts the cut itself, so there is no pilot hole and no drift off the chalk line. |
Self-tapping spiral ribs Continuous helical ribs cut their own thread in the gypsum core in one power-tool pass, roughly 8 seconds per fixing point. |
|
|
Ø14mm flange sits flush The wide flange stops against the board underside, spreading the load on the paper face and keeping the ceiling line flat instead of leaving a hook below it. |
Four expansion slots Four longitudinal slots in the ribbed body splay outward as the anchor seats, adding friction against the board core instead of crushing it. |
|
![]()
| Dimension | Metric | Imperial | Where It Matters |
|---|---|---|---|
| Overall length | 51mm | 2 inch | Tip and ribs go into the board, flange stays at the face |
| Tapered tip section | 15mm | 0.59 inch | Driven up into the board first, self-centring |
| Flange head diameter | Ø14mm | 0.55 inch | Stops flush at the underside of the board |
| Wire hole | Ø2mm | 0.078 inch | Takes 1.5–2.0mm suspension wire |
Tip up, flange down. The tapered point and the ribbed body are driven up through the plasterboard and stay held by the board core, while the flange sits flush on the underside and the wire leaves through the head hole. Nothing of the tip or the rib profile is left hanging below the ceiling line.
![]()
Section through the ceiling: tip and ribs in the board, flange flush at the face, wire through the 2mm head hole.
Office and retail ceilings: LED panel lights, troffer frames and linear fixtures hung from plasterboard without extra battens. The tapered end is driven into the board and the wire drops straight down to the panel, so the fixing stays tight to the ceiling line.
![]()
Three points, one panel: the tapered end of each anchor faces up into the board, the wire runs straight down and the panel is levelled from the wires. Nothing hangs below the ceiling except the wire.
![]()
| Material | Carbon steel, zinc plated |
| Overall length | 51mm (2 inch) |
| Head | Ø14mm flange, flush at the board underside, Ø2mm wire hole |
| Body | Spiral ribs with 4 expansion slots |
| Tip | 15mm tapered four-facet point, driven up into the board |
| Wire capacity | 1.5–2.0mm galvanised or stainless steel wire |
| Substrate | 9.5–12.5mm gypsum board, fibre board, PVC panel |
| Reference working load | 5kg per fixing in good condition 12.5mm board, factor 3 applied to on-site pull tests |
| Finish options | Clear zinc, yellow zinc, nickel, black oxide |
Which end goes into the board? The tapered tip goes up into the plasterboard first; the Ø14mm flange stays flush at the board underside and the wire leaves through the head hole.
Does it need a plastic plug inside the board? No. The ribs are held by the gypsum core directly, which removes one part from every fixing point.
Can I use it in a wet area? Choose the nickel or yellow zinc finish for bathrooms and kitchens where humidity is continuous.
YuYang Hardware – suspension cable grippers and drywall wire fixings, OEM and ODM.
Send your wire diameter, board thickness and target load, and we will quote the matching anchor within one working day.
Contact Person: Mrs. Jenny Liu
Tel: +86 15307696798